Water heater are those appliances which heat cold water. If you went for a shower and realise that your water heater is not working and it’s too late for protection and maintenance. Now it is important to call your local plumber when the water heater does not work and when it makes noise. If you are facing this kind of problem with your water heater and don’t know how to deal with it. Then you landed in the right place where we are going to tell you
how you can prevent your water heater at home.
Gas water heater maintenance
Maintaining the gas Water heater gives protection to your water heater and your water heater works for a longer span of time. You can enjoy hot water without a plumbing catastrophe. Here we are going to tell you the steps on how you can maintain your water heater.
Flush the gas water heater: The water heater work continuously in the winter season and most of the time mineral sets at the bottom of the tank and break down the water heater. When mineral takes place in the water, it can block your gas water heater and because of this operating difficulty, it can jam water lines too. So if you don’t want any blockage in your gas water heater then flush at least every year because flush is the main solution to clean them and cut out the mineral deposits.
Check the pressure pipe: Your gas water heater has a pressure tab and it’s called the TPR tap. It helps to discharge pressure when the tank goes over-pressured. For testing the TPR pipe, raise the lever on the tap and discharge it again. You will see a few glasses of water disappears and it also gives a hustling voice or a hint of an air issue in the pipe. If you don’t see all these things then you have to change the TPR pipe. It’s quite simple to check your gas water heater’s pressure pipe every six months to prevent it from blockage and leakage.
Check the filers: Some gas heater comes with filters to define the problem of the junk. Your water heater runs smoothly when it doesn’t face problems like sediment and junk deposits. It is important to change the filters frequently. Every heating problem has different phases and some aren’t caused by the appliances themselves but by the damaged regulator. The most important thing is the regulator because it only has the ability to heat all the appliances. It stops your gas water heater from burdening itself and keeps up with changeable temperature settings.
Check the anode rod: Anode is the most important element if your gas water heater works by cutting waste material in the water. Your gas water tank collects waste materials so it’s important to check the anode rod twice. Anode rods run up to 5 to 10 years, it is possible for the long run if you can clean them routinely.
Electric water heater maintenance
One of the important things is to maintain electric water heater maintenance. If you always want to maintain the water heater then you should go through a complete check time after time. So if you do this in the future you will not get in any trouble. Below we will share some important steps on how to maintain your Electric geyser.
Step 1.
- Before doing anything, first, turn off the electricity as well as the gas to abolish the pilot light. Close off the cold-water estuary to the water heater.
Step 2.
- Keep a bucket which can flow the water from the pressure relief tap. Extract the trip handle on the tap. You can hear the voice of the airflow. In between, you will notice another thing the water vapour leaves through the pressure relief valve if you can’t exhaust the tank and exchange the valve.
Step 3.
- To exchange the valve, the first thing you have to do is take out the discharge pipe and unscrew the tap from the water heater. Write down the length of a stem and purchase the same replacement. Place the new tap with good tightening with a wrench. econnect the discharge pipe, open the tap of water and either reconnect the electricity or start the pilot light again and follow the manufacturer’s instructions.
Now it’s time to flush the tank and remove all the dirt from the electric heater. The tank is built up by sediment which can reduce the water heater’s energy capability and also clog water lines. Neglect all these problems and increase the life of your component by blushing the tank every time. Don’t forget to check the pressure relief of the tap.
Water heater maintenance schedule
If you keep checking the water heater maintenance schedule, you can’t face any problems related to it. Do flush the water heater after four months. Clean the water heater for at least after one year. Change the anode rod every 2-5 years which is very important to the water heater. Clean and check the burner every year.
Water heater repair is important if repairs are not done at the exact time the water heater creates a lot of problems. If the hot water tank temperature goes high and pushes through the sediment of the upper of the tank, it will cause the sediment to move to other sides and down the water tanks, resulting in a following sound.
Who do you call to fix a water heater?
Fixing is very important for the water promptly because it can cause other problems too. So in this situation, you should call the plumber to fix a water heater. If the noise comes out from the water heater, the inside of the water heater is having some serious problem which is creating a loud sound. This sound is not safe for you because the water heater will explode at any time.
Conclusion If you are going through a water heater you have a problem with such as sound of knocking, screaming or tapping, prevent your water heater first. All this is not a good sign because day by day this problem goes on at an extreme level. So don’t take so much time and immediately call a plumber to fix the water heater.
